欄目導航
無紡布袋的設計制作要確定的事項
來源:http://www.52ylhc.com 作者:http://www.52ylhc.com 日期:2018/4/26 13:46:12 瀏覽次數:100
一、手提袋尺寸的確定
1. Determination of the size of a handbag
首先要確定手提袋的外觀、大小,而手提袋的容積規格與實際容納的體積緊密相關,太大則浪費紙張材料,太小不便于裝,也不好取。手提袋外觀尺寸確定后,就開始畫刀版圖紙了。
First of all, we must determine the appearance and size of the handbag, and the volume of the handbag is closely related to the actual volume, too big to waste paper material, too small to be easy to install, and not to take. When the size of the handbag is determined, the knife plate will be started.
二、刀版圖紙的繪制
Two. Drawing of the drawing of the knife
手提袋刀版圖紙可以在CAD軟件繪圖,也可以在AI、FH、CD等軟件內繪制。根據設計制作人員的特長而定,繪圖順序是先畫大面,再畫粘口及其他折痕部位,然后調整細節,最后檢查標注尺寸。
The handbag version can be drawn in CAD software or in software such as AI, FH and CD. According to the specialty of the design and production personnel, the drawing order is to draw the large surface first, then draw the sticky and other creases, then adjust the details, and finally check the dimensioning size.
三、外觀的設計與工藝制定
Three, design and process of appearance
1、外觀設定一般要與所裝物體的色彩、風格保持一致,最好能體現行業特性。
1, the appearance should generally be consistent with the color and style of the object, so it is best to reflect the characteristics of the industry.
2、正反面設計主要圖文在折痕處要避開。側面幾個折痕線交在一起的部位,最好不要有圖文,否則,折痕對其很有影響。就像設計煙包要避開反面折痕一樣。
2, design the main and negative text to avoid the creases. On the side of the crease lines, it is best not to have pictures or texts, otherwise, creases will have an impact on them. It's like designing a cigarette bag to avoid the reverse creases.
3、手提袋紙張與內面的包裝材料紙如果不一致,則在外觀上要盡量接近。
3. If the paper of the handbag paper and the inner surface are inconsistent, the appearance should be as close as possible.
4、覆膜要平整,尤其是覆光膜,膠水涂布不均勻,很容易花。
4, laminating should be smooth, especially film covering, uneven coating of glue, easy to spend.
1. Determination of the size of a handbag
首先要確定手提袋的外觀、大小,而手提袋的容積規格與實際容納的體積緊密相關,太大則浪費紙張材料,太小不便于裝,也不好取。手提袋外觀尺寸確定后,就開始畫刀版圖紙了。
First of all, we must determine the appearance and size of the handbag, and the volume of the handbag is closely related to the actual volume, too big to waste paper material, too small to be easy to install, and not to take. When the size of the handbag is determined, the knife plate will be started.
二、刀版圖紙的繪制
Two. Drawing of the drawing of the knife
手提袋刀版圖紙可以在CAD軟件繪圖,也可以在AI、FH、CD等軟件內繪制。根據設計制作人員的特長而定,繪圖順序是先畫大面,再畫粘口及其他折痕部位,然后調整細節,最后檢查標注尺寸。
The handbag version can be drawn in CAD software or in software such as AI, FH and CD. According to the specialty of the design and production personnel, the drawing order is to draw the large surface first, then draw the sticky and other creases, then adjust the details, and finally check the dimensioning size.

Three, design and process of appearance
1、外觀設定一般要與所裝物體的色彩、風格保持一致,最好能體現行業特性。
1, the appearance should generally be consistent with the color and style of the object, so it is best to reflect the characteristics of the industry.
2、正反面設計主要圖文在折痕處要避開。側面幾個折痕線交在一起的部位,最好不要有圖文,否則,折痕對其很有影響。就像設計煙包要避開反面折痕一樣。
2, design the main and negative text to avoid the creases. On the side of the crease lines, it is best not to have pictures or texts, otherwise, creases will have an impact on them. It's like designing a cigarette bag to avoid the reverse creases.
3、手提袋紙張與內面的包裝材料紙如果不一致,則在外觀上要盡量接近。
3. If the paper of the handbag paper and the inner surface are inconsistent, the appearance should be as close as possible.
4、覆膜要平整,尤其是覆光膜,膠水涂布不均勻,很容易花。
4, laminating should be smooth, especially film covering, uneven coating of glue, easy to spend.
上一條新聞:無紡布袋上的圖案是怎么制作上來的? 下一條新聞:手提袋制作黃色怎么設計才會更靚麗?