欄目導航
淺談無紡布等印刷品的燙金工藝
來源:本站 作者:jnjs 日期:2018/4/20 17:37:59 瀏覽次數:100
無紡布袋定做需要用到的工藝就包括燙金技術,而燙金要想獲得理想的燙印效果,燙印溫度、燙印壓力、燙印速度等工藝參數一定要合理掌握。另外,與燙金有關的原材料質量也必須有保障,比如:承印物的燙印適性、電化鋁材料的性能以及燙印版的質量等等。如果某一環節出了問題,必將影響到最終的燙印效果。
To get the ideal hot stamping effect, stamping process temperature, stamping pressure, hot stamping speed and other process parameters must be properly grasped. In addition, the quality of raw materials related to gold stamping must also be guaranteed, such as the printability of the printing material, the performance of the electrified aluminum material, and the quality of the stamping plate. If a part of the problem, will affect the final hot stamping effect.
選擇合適的承印物?梢誀C金的承印物很多,通常是紙張,如:銅版紙、白板紙、白卡紙、布紋紙、膠版紙等等。但并不是所有的紙張燙金效果都理想,如果表面粗糙、紙質疏松的紙張,例如對于書刊紙、較差的膠版紙等,由于電化鋁層不能很好地附著在其表面上,特有的金屬光澤不能很好地體現出來,甚至會燙印不上,因此,燙金的承印物應選用質地密實、平滑度高、表面強度大的紙張,這樣才能獲得良好的燙印效果,把特有的電化鋁光澤充分地體現出來。
Choose the right material. There are many substrates for bronzing, usually paper, such as coated paper, white board, white cardboard, cloth paper, offset paper, etc. But not all paper hot stamping effect is ideal, if the surface of rough, paper loose paper, for example, for book paper, poor offset paper, because the aluminum layer can not be well attached to its surface, the unique metallic luster can not be well embody, very hot stamping, therefore, hot stamping of the bearing. The printing material should choose the paper with dense texture, high smoothness and high surface strength. In this way, a good stamping effect can be obtained and the unique electrified aluminum luster is fully reflected.
根據承印物的不同選擇合適的電化鋁型號。電化鋁的結構有5層,即:聚酯薄膜層、脫落層、色層(保護層)、鋁層和膠層。電化鋁型號較多,常見的有l號、
To get the ideal hot stamping effect, stamping process temperature, stamping pressure, hot stamping speed and other process parameters must be properly grasped. In addition, the quality of raw materials related to gold stamping must also be guaranteed, such as the printability of the printing material, the performance of the electrified aluminum material, and the quality of the stamping plate. If a part of the problem, will affect the final hot stamping effect.
選擇合適的承印物?梢誀C金的承印物很多,通常是紙張,如:銅版紙、白板紙、白卡紙、布紋紙、膠版紙等等。但并不是所有的紙張燙金效果都理想,如果表面粗糙、紙質疏松的紙張,例如對于書刊紙、較差的膠版紙等,由于電化鋁層不能很好地附著在其表面上,特有的金屬光澤不能很好地體現出來,甚至會燙印不上,因此,燙金的承印物應選用質地密實、平滑度高、表面強度大的紙張,這樣才能獲得良好的燙印效果,把特有的電化鋁光澤充分地體現出來。
Choose the right material. There are many substrates for bronzing, usually paper, such as coated paper, white board, white cardboard, cloth paper, offset paper, etc. But not all paper hot stamping effect is ideal, if the surface of rough, paper loose paper, for example, for book paper, poor offset paper, because the aluminum layer can not be well attached to its surface, the unique metallic luster can not be well embody, very hot stamping, therefore, hot stamping of the bearing. The printing material should choose the paper with dense texture, high smoothness and high surface strength. In this way, a good stamping effect can be obtained and the unique electrified aluminum luster is fully reflected.
根據承印物的不同選擇合適的電化鋁型號。電化鋁的結構有5層,即:聚酯薄膜層、脫落層、色層(保護層)、鋁層和膠層。電化鋁型號較多,常見的有l號、
上一條新聞:無紡布袋的印刷方式都有哪些 下一條新聞:無紡布袋上的圖案是怎么制作上來的?